Skip to content

General Purpose Signal Conditioning Catalog

SIGnal Workbench

Catalog

Includes

  • 4 GPSC Transition Modules
  • 8 Filler Packs and Faceplates

Optional

  •  GPSC I/O Cards
  •  FPGA to GPSC Module Cables

The CQ9500TR-08 Conditioning Module features 32 galvanically isolated transformer channels and is intended to interface to AC signal applications requiring isolation such as LVDT, RVDT, synchro and resolver position sensors and simulators. For simulation applications, the module is intended to support eight excitation input channels and 16 output channels providing for eight dual output feedback channels; Va/Vb or sin/cos. The signal path is reversed for position sensing applications. All external channels are differential. The input channels can reference a common ground in order to function with single ended analog I/O channels. The outputs can be connected together to work in two, three or four wire configurations.

The signal conditioner can be used as a 32-channel input, 32-channel output, or any combination of inputs and outputs up to 32. The default configuration for the transformer signal conditioner is 16 input channels and 16 output channels. This configuration will support 16 2-wire LVDT channels.

Features:

±20V differential input (low side inputs can be tied together for single ended operation)
±20V differential output
10k Ohm impedance on the primary and secondary
Jumper selectable center tap on the primary and secondary windings
Galvanic isolation between inputs and outputs and individual channels
Transformer coil taps for doubling or halving input or output voltages
Bypassable filter capacitors to eliminate DC offset
16 transformers can be bypassed for 8 input and output channels for direct / DC values or offset are desired
Operating Temperature: -20C° to 85C°
Frequency Response: + 2.0 dB, at 300 Hz to 100K Hz (1 KHz Ref.)
Max power at 300Hz
Pri-Sec Hipot test (Pri-Sec): 1000 VRMS for 1 sec
External power supply not required.
DIN mount. Includes 6′ cable.

The Discrete Output Signal Conditioner takes a 0/3.3 volt or 0/5 volt single-ended logic input and outputs up to 0 / 40V or ±22 from common low/high power rails. The jumper selectable power rails provide a selection of +5V, +15V, -15V, GND from the default power supply. High-level external power rails V-A, V-B and low level external power rails G-A, G-B can be selected from additional power sources. V-A, V-B, G-A and G-B are isolated from signal and logic ground.

Features:

16 output channels
Digital Input: 3.3 to 5 volts
Maximum output: 0V/40V or -20V/+20V (40V maximum swing)
Four available on-board output rails to select: GND, +5V, +15V and -15V
Four external output rails to select: V-A, V-B, G-A, and G-B
Up to 1 MHz switching speed
Outputs are rated at up to 64mA per channel.
SI8640 isolators are utilized between inputs and outputs to improve noise immunity and protect input from possible transients.
0 to 100% duty cycle allows for high speed switching without sacrificing steady state stability.
Optional stackable expansion board adds 2 analog or discrete signals per channel selectable at output. Analog signals can be any voltage within the device limits of 0 to 40V or ±22

High-Speed Discrete Output Signal Conditioner, DIN Rail Mount​ (CQ9502-HDSO-16-DIN)

Prerequisite: 5V and +/- 15V power supply (CX-NPSC-PWR1)

The High power discrete output signal conditioner uses an isolated gate driver with 2 outputs to switch high side and low side power MOSFETS resulting in a high power, push pull output which is capable of sourcing or sinking voltages of up to 60V. The push pull configuration allows for switching speeds of up to 200kHz which high speed compared to most 60V capable devices. The high power discrete output signal conditioner is able to source or sink up to 1A continuous current with appropriately sized heat sinking options. The jumper selectable power rails provide a selection of +5V, +15V, -15V, GND from the default power supply. High level external power rails V-A, V-B and low level external power rails G-A, G-B can be selected from additional power sources. V-A, V-B, G-A and G-B are isolated from signal and logic ground.

Features:

8 output channels
Output voltage up to 60V
Outputs are rated at up to 1A per channel with appropriate heat sinks.
Switches up to 200kHz
Output: 0V/60V or -30V/+30V
Four available on-board output rails to select: GND, +5V, +15V and -15V
Four external output rails to select: V-A, V-B, G-A, and G-B
0 to 100% duty cycle
SI8640 isolators are utilized between inputs and outputs to improve noise immunity and protect input from possible transients

High Power Discrete Output Signal Conditioner, DIN Rail Mount (CQ9503-HPDO-16-DIN)

Prerequisite: 5V and +/- 15V power supply (CX-NPSC-PWR1)

The discrete input signal conditioner is a digital signal conditioning input board capable of converting a jumper configurable input voltage of 5V, 12V, 28V, or 60V into 5V logic level signal. Each of the 16 input channels can independently be configured for a 5V, 12V, 24/28V, or 60V input signal. Inputs are isolated from outputs providing protection and improved noise immunity. Each channel can be configured, via jumpers for either 5V logic level output, 15V output, or as a voltage sink capable of sinking a load of up to 30V, 15mA.

Discrete Input Signal Conditioner, DIN Rail Mount​ (CQ9501-DI-16-DIN)

Features:

16 input channels
Switching speeds of up to 2.5MHz.
Input voltage of 5V, 12V, 28V, or 60V
Output to 5V logic level signal
Input to output isolation
Channels can be utilized as 5V, 15V or Voltage sink Discrete Outputs, capable of sinking a load of up to 30V, 15mA.

Prerequisite: 5V and +/- 15V power supply (CX-NPSC-PWR1)

The analog output signal conditioner takes up to ±15V input and outputs up to 0 to 60V or ±30V. Jumper selectable gain options include gains of 1, 2, or 6. Each channel has jumper selectable configurations for inverting, noninverting, or differential outputs. Inputs can be single-ended or differential.

Features:

16 output channels
Single ended or differential inputs
Jumper selection for inverted, non-inverted, or differential output
Up to ±15V input
Outputs Sink/Source up to 50mA per channel
300kHz Bandwidth at unity gain, 50kHz full power bandwidth
Input can support analog or digital
Selectable output gain for up to 60V output

Analog Output Signal Conditioner, DIN Rail Mount​ (CQ9504-AO-16-DIN)

Prerequisite: 5V and +/- 15V power supply (CX-NPSC-PWR1)

The analog output signal conditioner takes up to ±60V input and has jumper selectable attenuations of 1, 2, or 6. Each channel has jumper selectable configurations for inverting, noninverting, or differential outputs. Inputs can be single-ended or differential.

Features:

  • 16 input channels
  • Single-ended or differential inputs
  • Jumper selection for inverted or non-inverted output
  • Up to ±60V input
  • Outputs Sink/Source up to 50mA per channel
  • Up to 300kHz Bandwidth
  • Input can support analog or digital
  • Jumper selectable attenuation of 1, 2, or 6

Analog Input Signal Conditioner, DIN Rail Mount (CQ9504-AO-16-DIN)

Prerequisite: 5V and +/- 15V power supply (CX-NPSC-PWR1)

4-Ch Enhanced Wheel Speed Sensor Card, DIN Rail Mount (CQ9512-WSS-4-DIN)

placeholder

placeholder

Power & Cables

placeholder

placeholder

placeholder

placeholder

placeholder

Back to top